2020 Parts Unlimited Tire

V-TWIN TOOLS www.dragnetweb.com BOLD MAGENTA part numbers are new for 2020 565 TAPPET GO-NO-GO TOOL • Simplifies the way to verify proper tappet adjustment • If the tip doesn’t fit between the clip and the pushrod seat or if there is up and down end play, then the tappet is out of adjustment • For use on most hydraulic tappets, OEM and aftermarket, for Twin Cam or Evo • Will not work on Solids, JIMS Hydrosolids or other limited travel tappets • Made in the U.S.A. VACUUM LIFTER PUMP UP TOOL • Bleeds and pumps up hydraulic lifters • Special jar, designed for vacuum, holds up to four hydraulic lifters in a convenient tray • Apply the vacuum to fully bleed the lifters and have them ready to install • Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196089 For 55-06 Big Twin, except 06 Dyna $239.95 PART # DESCRIPTION SUG. RETAIL DS-196105 For 40-99 Big Twin (except Twin Cam) and 52-76 XL $809.95 CRANKCASE MAIN BEARING LAP TOOL • Performs easy, precise alignment and lapping of right and left crankcase races for oversize bearings • Sold individually • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0318 For 17-20 M-Eight and 99-17 Twin Cam $73.95 CYLINDER HOLD DOWN NUTS • Help to keep the cylinders in place when removing the heads from the engine • One end fits Twin Cam models and the other fits M-Eight engines • Sold in a set of two • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0345 For 17-20 M-Eight 107”, 114” $565.95 3801-0130 For 99-17 Twin Cam 88”, 96” or 103”, 3.75”-3.875” 550.95 3801-0129 For 99-17 Twin Cam Screamin’ Eagle, 4”-4.060” 550.95 DS-196212 For 66-99 Big Twin cylinders, 3.4375”-4” bore w/ stock bolt pattern 542.95 DS-196213 Adapter bolt kit for 86-03 XL, 94-03 Buell (for use w/ PART #DS-196212) 43.95 CYLINDER TORQUE PLATES • Torque plates must be used when boring or honing late-model aluminum cylinders • Simulate running stress conditions • Instructions included • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 53-0005 For 58-99 Big Twin motors (except Twin Cam) $29.95 CRANKPIN NUT CLEARANCE GAUGE • Used to mark clearance between the cases and crankpin nuts when using stroker flywheels • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196155 For 57-85 XL $47.95 TAPPET GUIDE PULLER TOOL • Used to remove press-fit tappet guides from crankcase • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0251 Tappet adjustment tool $30.95 PART # DESCRIPTION SUG. RETAIL 3801-0192 Tappet pump and test stand for 99-20 Big Twin hydraulic tappets $293.95 3801-0193 1 Adapter for 84-99 Evo hydraulic tappets 72.95 1 Must be used in conjunction with PART #3801-0192. TAPPET PUMP AND TEST STAND • Allows you to fill hydraulic tappets before assembling valve train • Helps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won’t pump up due to poor hydraulic unit fitment • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0292 For 84-20 Big Twin hydraulic tappet assemblies $85.95 3801-0193 3801-0192 DS-196212 3801-0345 CRANK ASSEMBLY REMOVING TOOL • Use to press flywheels from cases • Will press cases apart and break sealant bond • Made in the U.S.A. NOTE: On Twin Cam B motor will only remove flywheel from left case.