2020 Drag FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES www.dragnetweb.com SECTION 7 All part numbers in BLUE are new for 2020. 731 DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGE 418 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION. See OLDBOOK For Early Model Applications PART # DESCRIPTION SUG. RETAIL FOR 07-17 TWIN CAM (AND 06 DYNA) 0925-0110 1, 2 For chain or gear drive cams $349.95 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0920-0006 3 For gear drive cams 359.95 0925-0109 3, 4 For chain drive cams w/ spring tensioners 379.95 0925-0440 5 Hydraulic tensioner conversion camplate for stock chain drive cams 349.95 HIGH FLOW CAMPLATES FOR TWIN CAM • Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages • Camplate matches the oil portholes throughout the camplate to the port holes in the engine case increasing engine oil flow throughout the engine • 25-35 degree cooler engine temperatures and 20- 30 degree cooler oil temperatures • Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE ® and other aftermarket camplates • The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings • Camplates are pressure tested and pressure relief valve is seated, sealed and set to pop off at 55-60 psi • When matched with the Feuling ® Race Series oil pump rear wheel power gains of 3 Horsepower and 4 ft/lbs of Torque can be achieved • For use ONLY with the Feuling ® oil pumps • Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerances for improved press fit • Bearing and retainer plate hardware is included • Camplates for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal tolerance for improved cam fitment • Added cam journal oil groove for cold startup protection and increased cam journal lubrication • Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear • Made in the U.S.A. 0925-0110 0925-0440 PART # DESCRIPTION SUG. RETAIL 0925-0914 For 07-17 Twin Cam and 06 Dyna models $367.95 0925-0915 1 For 99-06 Twin Cam models (except 06 Dyna) w/ gear drive cams 367.95 1 Accepts 07-17 style oil pumps only. TC3 CAM PLATE • Precision CNC-machined forged aluminum • Adjustable oil pressure regulator; adjust without removing plate from the engine • Passage plugs are removable for service • Rebuildable bronze pinion shaft bushing in all models and bronze cam bushings in 07-later style • Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later style oil pumps. 0925-0914 PART # DESCRIPTION SUG. RETAIL 0950-0891 For 17-20 M-Eight, 07-17 Twin Cam and 06 Dyna Glide $11.95 HYDRAULIC TENSIONER BLOCK OFF PLATE KIT • Block off the hydraulic cam chain tensioner holes when using gear-driven cams • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0932-0036 For 17-20 M-Eight, 07-17 Twin Cam and 06 Dyna cam plates $29.95 BLOCK OFF PLATE KIT • Block off hydraulic chain tensioner holes when using gear-driven cams • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 2401-0993 1 For 17-20 M-Eight engines w/ Feuling high flow camplate and HP+ or Race Series oil pumps (do not use washers with ARP ® oil pump bolts) $39.95 2401-1047 For 17-20 M-Eight engines w/ Feuling OE+ camplate and factory HD oil pump (requires use of washers with ARP ® oil pump bolts) 39.95 2401-0127 For 99-17 Twin Cam engines w/ Feuling HP+ or Race Series camplates and oil pumps 39.95 2401-0953 For 99-17 Twin Cam engines w/ Feuling OE+ camplates and oil pumps 39.95 1 Not for use with OE+ camplates/oil pumps. CAM PLATE/ OIL PUMP FASTENER KITS • Optional kit for Feuling camplates/oil pumps only • Quality 12-point, heat-treated 8740 chromoly steel bolts with black oxide finish manufactured by ARP ® to Feuling’s exact specifications • Precision-rolled threads provide optimum engagement, prevent galling and promote consistent torque loading • Wide, underhead flange design provides even load distribution for optimum sealing of surfaces to prevent leaks • Tensile strength rated at 170,000 psi; superior and stronger than OEM and stronger than grade 8 fasteners • Includes moly assembly lubricant for installation • Made in the U.S.A. 2401-1047 2401-0127 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 Requires the use of 07-17 style Feuling HP+ or Race Series oil pump PART #s0932-0023 or 0932-0026. 3 Requires the use of 99-06 style Feuling HP+ or Race Series oil pump PART #s 0932-0018 or 0932-0020. 4 Includes tensioner pins and guide hardware. 5 Requires 07-17 hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kit PART #s 0925-1069 or 0925-1070.