2020 Drag FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATEFRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES www.dragnetweb.com All part numbers in BLUE are new for 2020. SECTION 7 730 DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGE 418 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION. See OLDBOOK For Early Model Applications PART # DESCRIPTION SUG. RETAIL 0932-0193 For 17-20 M-Eight $299.95 OE+ CAMPLATE FOR M-EIGHT • Feuling ® OE+ stock replacement billet cam plates are manufactured from 6061 aluminum, providing increased rigidity and machined to Feuling’s high tolerance standards • Direct bolt-in replacement and accept the factory OEM oil pump only • Blueprinted and matched oil passages to the engine case passages, kidney shapes are designed to maximize flow • Optimizes oil flow to and from the oil pump and in and out of the engine, aiding in reducing oil and engine temps • Tighter cam journal bore tolerance for improved cam fitment • Added cam journal oil groove for cold start up protection and increased cam journal lubrication • Added oil pressure feed holes to front and back of cam journal to prevent excessive thrusting wear • For gear or chain drive cams (block- off plate PART #0932-0036 required when using gear drive cams) • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0932-0192 For 17-20 M-Eight $379.95 HIGH FLOW CAMPLATE FOR M-EIGHT • Increases engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including the scavenging return holes from the pump to the camplate and into the engine case • Camplate matches the oil portholes on the camplate to the oil holes in the engine case to increase oil flow throughout the engine • Lowers engine temperatures by 15-25 degrees and oil running temperature by 15-25 degrees when matched with a Feuling HP+ or RS oil pump • 7075 billet aluminum construction, which is 50% harder and stronger than the factory cast and Feuling ® OE+ camplates • Increases the strength and hardness of the camplate, holding tighter tolerances under temperature and eliminating flexing and the need for bronze bushings • When matched with the Feuling ® Race Series Oil Pump, rear wheel power gains of 2 horsepower and 2 ft. lb. of torque can be achieved • For gear or chain drive cams (block-off plate PART #0932-0036 required when using gear drive cams) • Made in the U.S.A. NOTE: For use ONLY with Feuling HP+ and Race Series M-Eight oil pumps. PART # DESCRIPTION SUG. RETAIL FOR 07-17 TWIN CAM (AND 06 DYNA) 0925-0842 1, 5 For chain or gear drive cams $259.95 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-0839 2 For gear drive cams 259.95 PART # DESCRIPTION SUG. RETAIL FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) (CONT) 0925-0840 2, 3 For chain drive cams w/ spring tensioners $279.95 0925-0841 4 Hydraulic tensioner conversion camplate for stock chain drive cams 259.95 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 For use with factory or any Twin Cam oil pump with the 99-06 bolt pattern. Compatible with Feuling oil pump PART #s 0932-0018, 0932-0089, 0932-0020. 3 Includes tensioner pins and hardware guide. 4 Requires 07-17 style oil pump, hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kits 0925-1069 or 0925-1070. Compatible with Feuling oil pump PART #s 0932-0090, 0932-0023, 0932-0026. 5 For use with factory and or any Twin Cam oil pump with ‘07-’17 bolt pattern; compatible with Feuling oil pump PART #0932-0090, 0932-0023, 0932-0026. OE+ CAMPLATES FOR TWIN CAM • Billet camplates are manufactured from 6061 aluminum providing increased rigidity and machined to Feuling ® high tolerance standards • Designed and manufactured to the highest standard of quality with proven Feuling ® performance • The pressure relief valve and spring are pre-set, matched and seated by Feuling ® with a full pop off pressure of 50-60 psi • Camplates for ‘99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerance for improved press fit • Bearing retainer plate and hardware included • Camplate for 99-17 Twin Cam (and 06 Dyna) have tighter cam journal bore tolerance for improved cam fitment • Added cam journal oil groove for cold start up protection and increased cam journal lubrication • Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear • Made in the U.S.A. 0925-0842 0925-0839