2023 NEW PRODUCTS WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for 2023. SECTION 1 NP88 See OLDBOOK For Early Model Applications DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGES 5 AND 6 FOR IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PART# DESCRIPTION SUG. RETAIL FOR 17-22 M-EIGHT 0926-3416 .675" lift (seat pressure 86 lb.) (Titanium spring retainers) $661.11 0926-3417 .675" lift (seat pressure 86 lb.) (Steel spring retainers) 546.73 0926-3420 .630" lift (seat pressure 101 lb.) (Titanium spring retainers) 634.37 0926-3421 .630" lift (seat pressure 317 lb.) (Steel spring retainers) 528.57 ROCKER VALVE SPRING CONVERSION KIT WITH RACING VALVE SPRINGS • Conversion kit uses Kibblewhite racing springs combined with a lightweight valve spring retainer that houses a standard 9.5 mm hardened steel shim • Rocker arm rides directly on the 9.5mm shim surface, allowing for a significantly greater rocker arm swipe surface area • Increased rocker arm surface contact area allows the ability to run higher lift cams than previously could not be used with valves having a 6mm valve stem • Rocker shim thickness can be varied by changing shim size to adjust the effect valve stem protrusion height • Increase in valve stem protrusion height with this kit is approximately 0.100" • Feature interference-wound, double-chrome silicone springs • Made in the U.S.A. NOTE: To maximize shim contact in the retainer, Kibblewhite strongly recommends tipping (shortening the valve tip). NOTE: Kibblewhite strongly recommends the use of titanium valves with these kits. 0926-3420 0926-3416 PART # DESCRIPTION SUG. RETAIL FOR 17-22 M-EIGHT 0926-3418 .625" lift (seat pressure 85 lb.) (Titanium retainers) $519.32 PART # DESCRIPTION SUG. RETAIL FOR 17-22 M-EIGHT (CONT) 0926-3419 .625" lift (seat pressure 85 lb.) (Steel retainers) $446.82 0926-3418 ROCKER VALVE SHIM CONVERSION KIT WITH BEEHIVE VALVE SPRINGS • Conversion kit uses Kibblewhite beehive springs combined with a lightweight valve spring retainer that houses a standard 9.5 mm hardened steel shim • Rocker arm rides directly on the 9.5mm shim surface, allowing for a significantly greater rocker arm swipe surface area • Increased rocker arm surface contact area allows the ability to run higher lift cams than previously could not be used with valves having a 6mm valve stem • Rocker shim thickness can be varied by changing shim size to adjust the effect valve stem protrusion height • Increase in valve stem protrusion height with this kit is approximately 0.100" • Progressively wound springs using Kobe super-clean, chrome silicon-based wire that is heat-treated and shot peened • Made in the U.S.A. NOTE: To maximize shim contact in the retainer, Kibblewhite strongly recommends tipping (shortening the valve tip). NOTE: Kibblewhite strongly recommends the use of titanium valves with these kits.
RkJQdWJsaXNoZXIy OTcxOTk3