*DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES ROAD RAGE STAINLESS 2-INTO-1 EXHAUST SYSTEM WITH “SUPER BIKE” MEGAPHONE MUFFLER* • Stainless steel construction with hand TIG welding • Stepped 1 3/4” to 1 7/8” headpipes welded to collector and Megaphone muffler • Partial stainless heat shields RADIAL SWEEPERS* • Stepped 1¾” to 2” headpipes • 16-gauge construction • O2 sensor port plugs included for non-sensor applications PART # DESCRIPTION SUG. RETAIL 1800-2556 For 18-22 FLSB and 22 FXLRST $1499.95 • Full-coverage heat shields • Mad in the U.S.A. • Utilizes an advanced inner collector for maximum performance • Includes 18mm O2 sensor ports and 12mm adapters • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 14-20 XL1200C/1200CX/1200T 1800-2465 Chrome w/ chrome heat shields $824.95 1800-2464 Black w/ black heat shields 857.95 1800-2465 THE DRAG SPECIALTIES AUGUST 2022 dragspecialties.com
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 2 *DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES 2-INTO-1 MEGAPHONE SYSTEM* • Stainless steel construction • Features completely rebuildable core • Low-to-mid range power gains of 15%-20% • 18mm O2 ports with 12mm adapters and plugs for carb models V-5 SLIP-ON MUFFLER* • 5” disc-based stainless tunable muffler with USFS approved spark arrestor • Features two center pull retainer clamps that allow for slippage rather than breaking in the event of a tip over • Almost six pounds lighter than stock • Stainless S-bend connector pipe increases boot clearance • Includes 22 pre-installed discs for a deep, low tone • Also includes all necessary hardware for simple installation PART # DESCRIPTION SUG. RETAIL 1800-2551 For 04-22 XL 883/1200 $798.95 PART # DESCRIPTION SUG. RETAIL 1801-1501 For RA1250/1250S Pan America $598.95 • Substantial 13.25 lb. weight savings • 4”disc-based tunable system • Includes 20 discs, closed end cap and mounting bracket
AUGUST 2022 THE DRAG SPECIALTIES 3 dragspecialties.com *DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES GLOSS BLACK AIR WING® RACK FLAG MOUNTS WITH FLAG • Rear flag mount attaches to the vertical mounting bar of the Air Wing® luggage rack • Allows use of the entire luggage rack • Includes American flag • Made in the U.S.A. GLOSS BLACK EXTENDED STYLE LUGGAGE RACK FLAG MOUNT WITH FLAG • Made from high-quality 303 stainless steel with a black powdercoat finish • Fit 1/2” or 5/8” horizontal round bars commonly found on Tour-Pak® luggage rack or detachable Air Wing® rack • Excellent alternative to plastic flags that mount on the side of the Pak • Mounts extend outward from the rack to make more room for luggage • Includes American flag • Includes Allen key for easy installation • Sold each • Made in the U.S.A. GLOSS BLACK FLAG MOUNT BASES • Made from high-quality 303 stainless steel with a black powdercoat finish • Allow for easy customization between flag mounts, flag size, flag design, pole size and pole topper design • Vertical bar mounts for use with 1/2” or 5/8” round bar commonly found of the Tour-Pak® luggage rack or the detachable Air Wing® rack • Easy installation (includes mounting tools) • Sold each • Made in the U.S.A. GLOSS BLACK TOUR PAK® SOLID FLAG MOUNTS WITH FLAG • Excellent alternative to plastic flags that mount on the side of the Pak • Made from high-quality 303 stainless steel with a black powdercoat finish • Pole is removable to easily change flags or put away for storage • Includes American flag • Includes Allen key for easy installation • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0521-1977 W/ 6” x 9” flag $94.95 0521-1978 W/ 10” x 15” flag 104.95 PART # DESCRIPTION SUG. RETAIL EXTENDED STYLE 1/2" ROUND BAR LUGGAGE RACK MOUNTS 0521-1967 W/ 6” x 9” flag $84.95 0521-1968 W/ 10” x 15” flag 99.95 PART # DESCRIPTION SUG. RETAIL EXTENDED STYLE 5/8" ROUND BAR LUGGAGE RACK MOUNTS 0521-1974 W/ 6” x 9” flag $84.95 0521-1975 W/ 10” x 15” flag 99.95 PART # DESCRIPTION SUG. RETAIL 0521-1955 5/8” round bar $60.95 0521-1956 1/2” round bar 70.95 PART # DESCRIPTION SUG. RETAIL WITH 6" X 9" FLAG 0521-1964 For 3/8” bars $84.95 0521-1965 For 5/8” bars 84.95 PART # DESCRIPTION SUG. RETAIL WITH 10" X 15" FLAG 0521-0437 For 5/8” bars $99.95 0521-1977 0521-1974 0521-1967 0521-1956 0521-1955 0521-1964
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 4 TOUR STEP-UP SEATS • Classic Step-Up performance with added passenger area comfort • Lattice stitch (LS) seats infuse old-school lattice stitch retro styling with a modern twist • Tuck-n’-roll (TR) seat features true tuck-n’-roll styling • High lumbar keeps the rider locked into the seat • Features Saddlemen’s Ultra-Foam which is formulated to provide a perfect balance of rigidity and user compliance with integrated GelCore™ technology • Whisper-grain SaddleHyde™ cover • Installs easily with all necessary mounting hardware and instructions included • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 97-07 FLHT/FLTR (EXCEPT FLHX) 0801-1429 Plain $495.00 0801-1430 Front & rear LS 495.00 PART # DESCRIPTION SUG. RETAIL FOR 97-07 FLHR/FLHX (EXCEPT FLHRS) 0801-1431 TR $495.00 0801-1432 Front LS 495.00 0801-1433 Plain 495.00 0801-1434 Front & rear LS 495.00 PART # DESCRIPTION SUG. RETAIL FOR 18-22 FXBB/FXST 0802-1456 TR $469.00 0802-1457 Front LS 469.00 0802-1458 Plain 469.00 0802-1459 Front & rear LS 469.00 PART # DESCRIPTION SUG. RETAIL FOR 18-22 FLSB/FXLR/FXLRS 0802-1460 TR $469.00 0802-1461 Front LS 469.00 0802-1462 Plain 469.00 0802-1463 Front & rear LS 469.00 TOUR STEP-UP SEATS • Classic Step-Up performance with added passenger area comfort • Lattice stitch (LS) seats infuse old-school lattice stitch retro styling with a modern twist • Tuck-n’-roll (TR) seat features true tuck-n’-roll styling • High lumbar keeps the rider locked into the seat • Features Saddlemen’s Ultra-Foam which is formulated to provide a perfect balance of rigidity and user compliance with integrated GelCore™ technology • Whisper-grain SaddleHyde™ cover • Installs easily with all necessary mounting hardware and instructions included • Made in the U.S.A. 0801-1430 0801-1431 0801-1432 0801-1429 0802-1456 0802-1457 0802-1462 0802-1463
AUGUST 2022 THE DRAG SPECIALTIES 5 dragspecialties.com ALTERNATING BRAKE STROBE MODULE • Plug-and-play brake strobe module takes alerting traffic behind you to the next level • When the brake is applied, the programmed flash or strobe pattern will alternate between left and right side lighting accessories creating an eye-catching pattern HANDLEBAR WIRE EXTENTION KITS • Wires of pre-cut lengths are prepped to easily extend OEM wires when installing taller handlebars • olor-matched wires include Molex terminals on each end • Equipped with pins and connectors • Plug-and-Play THROTTLE-BY-WIRE HANDLEBAR WIRE EXTENTION KITS • Wires of pre-cut lengths are prepped to easily extend OEM wires when installing taller handlebars • Color-matched wires include Molex terminals on each end • Equipped with pins and connectors • Plug-and-Play PART # DESCRIPTION SUG. RETAIL 2050-0461 For 14-22 FLHX/FLTRX/FLTRK/FLTRU/FLHT/FLHTCU/FLHTCUL/FLHTK/FLHR/FLHRXS $99.95 2050-0463 For 10-13 FLHX/FLTRX (except CVO models) 99.95 2050-0462 For 97-13 FLHT/FLHTCU/FLHTK/FLHR/FLHRC/FLTRU, 98-09 FLTR, 06-09 FLHX, 96-17 Softails (except FXSB/ FXSBSE/FXSE/FXCWC/FLS/FLSS/FXS/FLSTSE2 CVO), 97-17 Dyna, 99-03 XL 99.95 2050-0464 Universal for 12V DC negative ground systems 99.95 PART # DESCRIPTION SUG. RETAIL FOR 14-22 TOURING AND TRIKE, 11-22 SOFTAIL, 12-17 DYNA AND 14-22 XL (EXCEPT 21-22 SPORTSTER S/RH1250S) 2120-1170 8” extention kit $34.95 2120-1175 4” extention kit 33.95 PART # DESCRIPTION SUG. RETAIL FOR 08-13 FLHT/FLHTCU/FLHTK/FLHR/FLHX/FLTR/FLTRU/FLHTCUTG 2120-1174 15” extention kit $49.95 2120-1176 12” extention kit 39.95 PART # DESCRIPTION SUG. RETAIL FOR 08-13 FLHT/FLHTCU/FLHTK/FLHR/FLHX/FLTR/FLTRU/FLHTCUTG 2120-1171 15” extension kit $29.95 2120-1172 12” extension kit 29.95 PART # DESCRIPTION SUG. RETAIL FOR 08-13 FLHT/FLHTCU/FLHTK/FLHR/FLHX/FLTR/FLTRU/FLHTCUTG (CONT) 2120-1173 8” extension kit $29.95 2120-1177 4” extension kit 29.95 CUSTOM DYNAMICS Customizing electronics on modern bikes requires more than just wire cutters and solder. Custom Dynamics has the technical know-how and engineering skills to design and build true plug-and-play solutions to make installing custom LED lighting on your bike simple with reliable, eye-catching results. • Compatible with add-on custom LED lighting (such as Custom Dynamics® LED Boltz™ PART #s 2040-2838 and 2040-2839) when used as left and right side rear brake lights • Does not affect OEM rear brake lights • Sold each 2050-0461 2050-0464 2050-0462 2050-0463 2120-1171 2120-1172 2120-1170
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 6 FUELPAK FP4* • Built from the ground up, Android and iPhone apps feature a new rider interface and are easier to navigate and use than ever before • Live Data in the FP4 app has been upgraded with a whole new look and an additional gauge to track more crucial data while riding • All-new Performance Data feature allows rider to record their ride, look at all available sensors in the created chart and see a map of their ride recorded with their phone’s onboard GPS • Made of polycarbonate plastic/Bluetooth low energy, FP4 hardware smaller and thinner than the previous generation electronics product • Unit’s LEDs have been simplified so the rider knows exactly what is happening between the FP4 and the rider’s motorcycle • All necessary hardware and Instructions included • Made in the U.S.A. NOTE: Always wear proper safety gear and ride in a responsible manner. Legal in California only for racing vehicles which may never be used or registered or licensed upon a highway. O2 SENSOR • Front 12mm oxygen sensor • Gray connector 52", 4 wire • Precision made consisting of a ceramic body made of stabilized zirconium dioxide, surface coated with gas-permeable platinum electrodes and a porous ceramic to aid the prevention of erosion due to contamination and particulates in the exhaust gases • Slow oxygen sensors can cause a drop in fuel economy of 10-15%, excessive exhaust emissions and poor drivability • Life expectancy of an average oxygen sensor in a properly tuned engine is typically 30,000 - 50,000 miles • Meets or exceeds OE specifications • Made in the U.S.A. • Sold each FUEL INJECTOR • Factory OEM Fuel injector for M-Eight engines • Delivers fuel at 4.4 grams per second through multiple spray holes • Injector has EV-6 USCAR type connector • Recommended for factory replacement • Made in the U.S.A. CYLINDER HEAD TEMP SENSOR • Electronic engine management sensor found on the cylinder head • Measures the temperature of the cylinder head • Data is then sent to the ECU to calculate timing and fuel ratio for the engine • Like all sensors, they can fail over time and this may cause long cranking time, decrease in power, acceleration and fuel economy • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1020-3962 For 14-20 FLHT/FLHX/FLTRX/S/FLTRU/FLTRK/FLHT, 15-20 FLRT, 11-20 Softails, 12-17 Dynas (excluding 11-13 CVO Softails) 12-17 Dynas, 14-22 XL Sportster models (except 21-22 Sportster S/RH1250S and 22 Nightster RH975) and 15-20 XG500/750/750A $459.99 PART # DESCRIPTION SUG. RETAIL 1861-1647 For 17-22 Touring models $99.95 PART # DESCRIPTION SUG. RETAIL 1022-0275 For 17-22 M-Eight Touring and 18-22 Softails; repl. OEM #27400015 $97.95 PART # DESCRIPTION SUG. RETAIL 2212-0861 For 99-17 Twin Cam; repl. OEM #32446-99 $29.95 EXTERNAL BREATHER KITS* • Converts the Assault Charge Air Cleaner from internal to external breathing • Vents breathers to atmosphere instead of recirculating oil mist back through the intake • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1012-0255 All Twin Cam engines running an Assault Charge Air Cleaner $149.95 1012-0256 All M8 engines running an Assault Charge Air Cleaner 149.95 1012-0255 1012-0256 *DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES
AUGUST 2022 THE DRAG SPECIALTIES 7 dragspecialties.com RACE SERIES OILING SYSTEM/CAMCHEST FRESHEN UP KIT FOR TWIN CAM* • Freshen up camchest and oiling system on late model Twin Cam engines • Kit uses existing camshafts or allows purchase of preferred cam selection while upgrading camchest with a new Race Series high volume oil pump, High Flow camplate, Race Series full travel lifters, billet tensioner housings, tensioner pads, cam/c rank sprockets, sprocket alignment spacers, cam chains, cam bearings, hardware, gaskets and o-rings HP+ OILING SYSTEM/CAMCHEST FRESHEN UP KIT FOR TWIN CAM* • Freshen up camchest and oiling system on late model Twin Cam engines • Kit uses existing camshafts or allows purchase of preferred cam selection while upgrading camchest with a new HP+ high volume oil pump, High Flow camplate, HP+ lifters, billet tensioner housings, tensioner pads, cam/c rank sprockets, sprocket alignment spacers, cam chains, cam bearings, hardware, gaskets and o-rings PART # DESCRIPTION SUG. RETAIL 0932-0296 For all 07-17 Twin Cam and 06 Dyna $1,595.95 PART # DESCRIPTION SUG. RETAIL 0932-0295 For all 07-17 Twin Cam and 06 Dyna $1,379.95 • Made in the U.S.A. NOTE: Designed for use with 07-17 chain drive camshafts. See Feuling camshaft selection: PART #0928-0427 (525 Grind), PART #0925-0673 (543 Grind), PART #0925-0430 (574 Grind), PART #0925-0677 (594 Grind) and PART #0925-0433 (630 Grind). • Made in the U.S.A. NOTE: Designed for use with 07-17 chain drive camshafts. See Feuling camshaft selection: PART #0928-0427 (525 Grind), PART #0925-0673 (543 Grind), PART #0925-0430 (574 Grind), PART #0925-0677 (594 Grind) and PART #0925-0433 (630 Grind). *DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 8 TRACKBOARDS FLOORBOARDS • CNC-machined billet aluminum • Black anodized with Kodlin logo • Dimensions: 15.75” long, 5” wide, 0.75” thick • Include all hardware • Sold in pairs TRACKBOARDS BRAKE PEDAL PAD • CNC-machined billet aluminum • Lightweight design • Black anodized with “K” logo • Dimensions: 3.25” long, 5” wide, 0.75” thick • Sold each TRACKBOARDS MINI FLOORBOARDS • CNC-machined billet aluminum • Black anodized • Dimensions: 4” long, 6.5” wide, 0.75” thick • Requires Kodlin model specific splined adapters sold separately. • Sold in pairs TRACKBOARDS SHIFTER PEG • CNC-machined billet aluminum • Lightweight design, black anodized • Fits all HD models using traditional style 5/16NF screw in toe peg • Dimensions: 1” long, 2.5” wide, 0.65” thick PART # DESCRIPTION SUG. RETAIL 1621-1117 For 99-21 FLT/FLHT/FLHR/FLHX/FLTR/FLTRU/FLTRK, 09-13 H-D FL Trike, 00-17 FLST, AND 12-16 FLD $549.99 PART # DESCRIPTION SUG. RETAIL 1610-0652 For 99-21 FLT/FLHT/FLHR/FLHX/FLTR/ FLTRU/FLTRK, 09-13 H-D FL Trike, 00-17, AND 12-16 FLD $89.99 PART # DESCRIPTION SUG. RETAIL 1621-1118 Black $249.99 PART # DESCRIPTION SUG. RETAIL 1603-0380 Black $59.99 KODLIN USA Fred Kodlin had a vision to create custom bikes in a way the world hadn’t seen before. Founded in 1984, Kodlin has built a name in cutting-edge product design, high-quality manufacturing and delivering custom parts and accessories with distinct fit, form and function for your motorcycle.
AUGUST 2022 THE DRAG SPECIALTIES 9 dragspecialties.com LIFT KIT/SHOCK EXTENSION FOR M-EIGHT SOFTAILS • Lifts bike up to 1” • Includes new pre-installed bearings • No additional shock modifications required • Installs easily using a spring compression tool • Installation instructions included LIFT KIT/SHOCK EXTENSION • Provides extra ground clearance • Steel construction with black powder-coated finish • Easy installation -- no suspension modification required • Increases height 1” • No shock compression tool required • Downloadable installation instructions included BELT GUARD • Steel construction with black powder-coated finish • Stainless steel hardware included • Easy installation LOWERING KIT • Steel construction with black powder-coated finish • Easy installation -- no suspension modification required • Lowers height 1” • No shock compression tool required • Downloadable installation instructions included BATES-STYLE HEADLIGHT BRACKET • Steel bracket with black powder-coated finish • Converts M8 Softail Breakout LED headlight to fit a Bates-style headlight • Sold each; headlight sold separately PART # DESCRIPTION SUG. RETAIL 1304-1083 For 18-22 Softail models (except FXDR, Fat Bob, Heritage Softail and 22 Low Rider S/ST w/ factory extended shock) $139.99 PART # DESCRIPTION SUG. RETAIL 1304-1085 For 21-22 Sportster S/RH1250S $99.99 PART # DESCRIPTION SUG. RETAIL 1202-0167 For 21-22 Sportster S/RH1250S $99.99 PART # DESCRIPTION SUG. RETAIL 1304-1084 For 21-22 Sportster S/RH1250S $99.99 PART # DESCRIPTION SUG. RETAIL 2001-2509 For 18-21 FXBR/FXBRS $99.99
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 10 GRIPS • Seamless Rubber Grip technology • Billet aluminum end caps and collars • Match for Khrome Werks Edge, Turbine and Tracer muffler end caps • Fit bars made for 1” grips PART # DESCRIPTION SUG. RETAIL FOR 08-21 FLHT/FLHR/FLTRX/F LTRU/FLTRK/FLHX, H-D FL TRIKE, 16-21 SOFTAILS, 20-21 ELW, 16-17 FXDLS, 13-15 FXSBSE, 14-15 FLSTNSE, 11-12 FLSTSE 0630-2835 Contour Edge, black $105.95 0630-2837 Contour Edge, chrome 105.95 0630-2836 Air Cushion Edge, black 105.95 0630-2838 Air Cushion Edge, chrome 105.95 FOR 99-17 TWIN CAM AND 86-21 XL MODELS (EXCEPT 08-17 DRESSERS, H-D FL TRIKES, 16-17 SOFTAILS, 13-15 FXSBSE, 11-12 FLSTSE, 16-17 FXDLS AND MODELS W/ AIR-ASSISTED FORKS AND 21 SPORTSTER S/RH 1250S) 0630-2839 Contour Tracer 105.95 0630-2841 Contour Turbine 105.95 0630-2843 Contour Edge, black 105.95 0630-2845 Contour Edge, chrome 105.95 0630-2840 Air Cushion Tracer 105.95 0630-2842 Air Cushion Turbine 105.95 0630-2844 Air Cushion Edge, black 105.95 0630-2846 Air Cushion Edge, chrome 105.95 KHROME WERKS A new look in custom grips! Khrome Werks is excited to offer their new Edge grips in custom contour and air cushion styles. Available for cable or Throttle By Wire applications, they add comfort and style to your bike. • Available in Air Cushion or Contour style • Made in the U.S.A. See page 1285 of the 2022 Drag Specialties FatBook for the complete line of Khrome Werks grips 0630-2837 0630-2836 0630-2839 0630-2843 0630-2842 0630-2846
AUGUST 2022 THE DRAG SPECIALTIES 11 dragspecialties.com 1 1/2” EZ INSTALL FLAT TOP HANDLEBARS • Revolutionary interlocking bolt-together two-piece handlebar design that takes up half the shelf space, is economical to ship and even faster to install • CNC mandrel-bent from 1 1/2” diameter x .095” wall heavy tube • Adjustable 1 1/2“ diameter collars next to the handlebar controls for a custom finished look • EZ Install - no more need to fight internal wiring; with our handlebars you can install wiring in minutes • Feature a billet machined top with a large internal machined radius that allows for EZ pulling of wiring (non-welded top corner) 1 1/2” EZ INSTALL POINTED TOP HANDLEBARS • Revolutionary interlocking bolt-together two-piece handlebar design that takes up half the shelf space, is economical to ship and even faster to install • CNC mandrel-bent from 1 1/2” diameter x .095” wall heavy tube • Adjustable 1 1/2“ diameter collars next to the handlebar controls for a custom finished look • EZ Install - no more need to fight internal wiring; with our handlebars you can install wiring in minutes • Feature a billet machined top with a large internal machined radius that allows for EZ pulling of wiring (non-welded top corner) EZ CLUTCH ADJUSTER UPGRADE KIT • Converts the factory upper clutch cable adjuster to a screw-type ½”-20 adjuster • Reinforces the clutch cable • Works as a repair part for a broken HD factory cable adjuster CHROME SUG. RETAIL GLOSS BLACK SUG. RETAIL END RISE WIDTH CENTER WIDTH PULLBACK FOR 21-22 FLTRX/FLTRXS/FLTRK/FLTRXSE/FLTRXST/FLTRXSE 0601-5795 $524.95 0601-5898 $524.95 12” 35” 10 1/4” 8” 0601-5796 524.95 0601-5799 524.95 14” 35” 10 1/4” 8” 0601-5797 524.95 0601-5800 524.95 16” 35” 10 1/4” 8” FOR 99-13, 21-22 FLHT/FLHT/FLHTK/FLHTKSE/FLHX/FLHXS/FLHXSE/FLHTCI/FLHTCUSE/FLHTPI/FLHTCUTG/FLHTCUTGSE 0601-5789 $524.95 0601-5792 $524.95 12” 36” 15” 9” 0601-5790 524.95 0601-5793 524.95 14” 36” 15” 9” 0601-5791 524.95 0601-5794 524.95 16” 36” 15” 9” CHROME SUG. RETAIL GLOSS BLACK SUG. RETAIL END RISE WIDTH CENTER WIDTH PULLBACK FOR 21-22 FLHRXS 0601-5783 $524.95 0601-5786 $524.95 12” 35” 10 1/4” 8” 0601-5784 524.95 0601-5787 524.95 14” 35” 10 1/4” 8” 0601-5785 524.95 0601-5788 524.95 16” 35” 10 1/4” 8” PART # DESCRIPTION SUG. RETAIL 0660-0014 For 22 FL Touring and 22 Softail with cable clutch $49.95 • Bars with “squared” lower bends also have additional slots to ease wire routing • Bars are knurled and notched for TBW applications • Made in the U.S.A. NOTE: Accept OEM heated grips. NOTE: U.S. Patent No. 10,946,926 • Bars with “squared” lower bends also have additional slots to ease wire routing • Bars are knurled and notched for TBW applications • Made in the U.S.A. NOTE: Accept OEM heated grips. NOTE: U.S. Patent No. 10,946,926 • Works with stock clutch cable and Fat Baggers EZ Clutch Extensions • Made in the U.S.A. 0601-5795 0601-5794 0601-5786 0601-5785
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 12 KARBONFIBR DESIGNER DOT HANDLEBAR INSTALLATION KITS • The only complete kits with matching braided cables and DOT brake lines • Kits include Throttle-By-Wire extensions, clutch cable or hydraulic clutch line, brake lines, copper crush washers, hardware and any necessary switch wiring or turn signal extension • Select kits are also available with Quick Connect upper clutch cables that reuse the existing lower clutch section • All cables and DOT brake lines feature KarbonFibr braid with highly polished black chrome-plated fittings • KarbonFibr braid is created from metallic wire with distinct black tone colors, blended and interwoven to mimic the distinct look of carbon fiber • Brake lines are constructed with PTFE inner tubing, DuPont™ Kevlar® aramid fiber, premium Signature • Magnum braids and an outer PVC jacket DESCRIPTION 10” APES 12”-14” APES 15”-17” APES TOURING For 21 FLHRXS (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line) - 0662-1032 0662-1033 For 21 FLHR (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line) - 0662-1037 0662-1038 For 21 FLHT, FLHTK/S, FLHX/S (w/ Quick Connect Upper Clutch cable and full length brake line) - 0662-1084 0662-1085 For 21 FLHT, FLHTK/S, FLHX/S (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and lower brake line) 0662-1059 0662-1057 0662-1058 For 21 FLTRK, FLTRX, FLTRXS (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line) - 0662-1034 0662-1035 SOFTAIL For 18-20 FLDE, 18-21 FLFB/S, FLHC/S, FLSB, FLSL (w/ ABS) (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line; includes an adapter) - 0662-1070 0662-1071 For 18-20 FXBR/S, 18-21 FXBB/S, 18-20 FXLR (w/ ABS) (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line; includes an adapter) - 0662-1070 0662-1071 For 18-21 FXFB/S (w/ ABS) (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line; includes an adapter) - 0662-1039 0662-1040 For 20-21 FXLRS (dual disc w/ ABS) (w/ Quick Connect Upper Clutch cable; uses existing lower clutch cable and brake line; includes an adapter) - 0662-1039 0662-1040 PART # SUG. RETAIL 0662-1032 $405.95 0662-1033 405.95 0662-1034 359.95 0662-1035 359.95 PART # SUG. RETAIL 0662-1037 $364.95 0662-1038 364.95 0662-1039 334.95 0662-1040 334.95 PART # SUG. RETAIL 0662-1057 $382.95 0662-1058 382.95 0662-1059 299.95 0662-1070 334.95 PART # SUG. RETAIL 0662-1071 $334.95 0662-1084 639.95 0662-1085 639.95 PRICE LIST • All cables are a low-effort, high-efficiency design that meets or exceeds all OE specifications for fitment, construction and endurance • Kits for dual disc models include an all brazed manifold that eliminates leaks, alignment problems and unattractive threaded connections • Brake lines are compliant with all DOT FMVSS-106 Specifications • Assembled in the U.S.A. • DuPont™ and Kevlar® are trademarks or registered trademarks of E.I. du Pont de Nemours and Company. NOTE: Kits are based on using ape hanger style handlebars with 2” risers; except Touring models. 0662-1032 0662-1070 0662-1033
AUGUST 2022 THE DRAG SPECIALTIES 13 dragspecialties.com XR STAINLESS DOT HANDLEBAR INSTALLATION KITS • Magnum XR DOT Handlebar Installation Kits offer a great fit and excellent quality at an economical price • XR DOT Handlebar Installation Kits are available for popular ABS HarleyDavidson® motorcycles with 12” to 17” ape hanger style handlebars • Available with Quick Connect upper clutch cables that reuse the existing lower clutch section • Three color combinations to complement your bike: clear-coated stainless steel with chrome fittings, black-coated with chrome fittings or black-coated with black fittings • All cables are a low-effort, high-efficiency design that meets or exceeds all OE specifications for fitment, construction, endurance • Magnum XR DOT brake lines use an enhanced construction of heavy gauge stainless steel embedded in tough abrasion-resistant nylon outer jacket for superior durability PART # SUG. RETAIL 0662-1086 $449.95 0662-1087 449.95 PART # SUG. RETAIL 0662-1088 $419.95 0662-1089 419.95 PART # SUG. RETAIL 0662-1090 $424.95 0662-1091 424.95 DESCRIPTION STAINLESS W/ CHROME FITTINGS 12”-14” STAINLESS W/ CHROME FITTINGS 15”-17” BLACK W/ CHROME FITTINGS 12”-14” BLACK W/ CHROME FITTINGS 15”-17” BLACK W/ BLACK FITTINGS 12”-14” BLACK W/ BLACK FITTINGS 15”-17” For 21 FLHT/FLHTK/FLHX/FLHXS w/ ABS (w/ Quick Connect Upper Clutch cable and full length brake line) 0662-1090 0662-1091 0662-1088 0662-1089 0662-1086 0662-1087 PRICE LIST • The coating on cables and brake lines offers exceptional protection for paint or chrome • Kits that include manifolds use an all-brazed construction to ensure optimal OE fitment and appearance • Manifolds use AN-3 connections for an easy installation • Kits include Throttle-By-Wire extensions, clutch cable, XR DOT brake lines, copper crush washers, hardware, fully terminated turn signal and switch wiring extensions • Brake lines are compliant with all DOT FMVSS-106 Specifications NOTE: Kits are based on using ape hanger style handlebars and 2” risers (except Touring models). BIG SUCKER™ STAGE 1 AIR CLEANER • One-piece aluminum backing plate features hidden breather technology • Each hidden breather is O-ringed at the heads and exits at the mouth of the injector/ carb to provide efficient engine breathing, eliminating the need for any external hoses or hardware • Radius air inlet provides maximum performance by providing unobstructed airflow • Backing plates has a black powdercoat finish • Standard red filters are pre-oiled, washable and feature four layers of surgical-grade cotton for optimum filtration and maximum airflow 49MM FORK TUBES • Specially coated DLC black or gold nitrate • Available in stock factory length (22 7/8”) or +2” length (24 7/8”) • Designed to work with both factory & aftermarket front ends • Accepts all 2017-2022 factory suspension internals • Aftermarket suspension internals require the use of 2017-2022 FLT fitment performance kits PART # DESCRIPTION SUG. RETAIL 1010-2941 For 01-17 Twin Cam Delphi EFI models and 99-06 Twin Cam CV carb models (except 08-17 FLHT/FLHR/FLHX/FLTR/H-D FL Trike, 16-17 Softails, 16-17 FXDLS, 08-17 FXD/FXDWG) $179.95 PART # DESCRIPTION SUG. RETAIL 0404-0642 Gold, 22 7/8” (stock) $459.95 0404-0644 Gold, 24 7/8” (+2”) 599.95 PART # DESCRIPTION SUG. RETAIL 0404-0643 Black, 22 7/8” (stock) $459.95 0404-0645 Black, 24 7/8” (+2”) 599.95 0404-0644 0404-0645 • All necessary hardware and instructions are included with each kit • Accepts Ness Stage I round covers only NOTE: Exempt per CARB Executive Order (E.O.) # D-639-10 for 2001-2017 EFI models only. 0662-1090 0662-1086 0662-1088 FOR 17-22 FLHT/FLHR/FLHX/FLTRX/FLTRU/FLTRK MODELS
AUGUST 2022 THE DRAG SPECIALTIES dragspecialties.com 14 DYNOJET "Hard Parts for the Pan America" The Pan AmericaTM is taking riders on all sorts of new on- and offroad adventures. Make sure your bike is ready with accessories from Dynojet. Axle sliders, chain guards, chain adjusters, levers and more. Improve your bike’s style and up the impact protection before your next adventure ride with accessories from Dynojet. IGNITION COIL GUARD • Protects the ingnition coil in the event of a tip over • Made from 6061-T6 aluminum • Hard anodized in stealth gray finish • Easy installation • Made in the U.S.A. CHAIN GUARD • Billet aluminum guard deflects rocks and shields the drive system from impacts which would derail the chain • Constructed of 6061-T6 aluminum and reinforced between the tabs • Hard anodized stealth gray finish • Made in the U.S.A. AXLE SLIDER KITS • Constructed of high-quality acetal plastic material to keep the axle protected in case of a fall or if the terrain adds rocky ruts to your path • Designed to hold tight sealing inside your axle, keeping dust and debris at bay • Easy, no-tool assembly • Sold as a set, including right/left pair • Made in the U.S.A. BRAKE PEDAL EXTENDER • Adds height to the brake pedal for a more comfortable standing position • Made from 6061-T6 aluminum • Hard anodized in stealth gray finish • Made in the U.S.A. CHAIN BLOCK ADJUSTERS • Replaces the stock chain adjusters • Made of 6061-T6 aluminum • Captures the nut on the left-hand side • Hard anodized in stealth gray finish • Made in the U.S.A. SIDESTAND SWITCH GUARD • Protects the vulnerable sidestand switch • Made from 6061-T6 aluminum • Hard anodized in stealth gray finish • Made in the U.S.A. REAR BRAKE RESERVOIR GUARD • Protects the vulnerable brake reservoir on the right-hand side of the bike • Made from 6061-T6 aluminum • Hard anodized in a stealth gray finish • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 2102-0440 For 21-22 RA1250/1250S models $244.43 PART # DESCRIPTION SUG. RETAIL 1202-0166 For 21-22 RA1250/1250S models $77.77 PART # DESCRIPTION SUG. RETAIL 0214-2139 Front $55.54 PART # DESCRIPTION SUG. RETAIL 0214-2140 Rear $55.54 PART # DESCRIPTION SUG. RETAIL 1610-0651 For 21-22 RA1250/1250S models $99.99 PART # DESCRIPTION SUG. RETAIL 1231-1568 For 21-22 RA1250/1250S models $66.66 PART # DESCRIPTION SUG. RETAIL 0510-0628 For 21-22 RA1250/1250S models $55.54 PART # DESCRIPTION SUG. RETAIL 1731-0770 For 21-22 RA1250/1250S models $55.54 FOR 21-22 RA1250/1250S MODELS 0214-2140 0214-2139
AUGUST 2022 THE DRAG SPECIALTIES 15 dragspecialties.com APEX DRIVER FLOORBOARDS • Designed with maximum ground clearance without sacrificing comfort • Fit perfectly over stock HD mounts • Constructed from 6061 billet aluminum • 10” L and 4.2” W at widest point • Machined deleon plastic scrape plate • Optional lift kit and tail extension available separately • Lift kit increases ground clearance by .5” • Tail extension increases length by 1.2” and gives a 5° angled tail to the back of the floorboards • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL FOR 07-22 TOURING MODELS 1602-1444 Black $119.95 PART # DESCRIPTION SUG. RETAIL FOR 07-22 TOURING MODELS 1602-1445 Chrome $139.95 1621-1110 1621-1114 1621-1112 1621-1111 1621-1116 1602-1444 1602-1445 TUNED INDUCTION SYSTEM REPLACEMENT AIR FILTER* • High-flow cotton filter media provides increased airflow for better performance • Washable and reusable PART # DESCRIPTION SUG. RETAIL 1011-4631 Replacement air filter $33.95 • Tapered design • Sold each • Made in the U.S.A. *DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES PART # DESCRIPTION SUG. RETAIL FOR 80-22 FLHT/FLHR/FLHX/FLTR/FLTRU/FLTRK/FLTRX, 09-13 H-D FL TRIKE, 87-17 FLST AND 12-16 FLD 1621-1110 Black floorboards $479.95 1621-1111 Chrome floorboards 479.95 1621-1112 Tail extension w/ lift kit, black 159.95 1621-1113 Tail extension w/ lift kit, chrome 159.95 1621-1114 Lift kit 79.95 1621-1115 Tail extension, black 149.95 1621-1116 Tail extension, chrome 149.95 EZ SHIFT LEVERS • Sturdy 6061-T6 aluminum construction • Improves shifting leverage by 25% • Makes it easier to shift gears and find neutral • Reduces force required to move the shift peg from 13 ft/lb to 10 ft/lb • Includes hardware • Made in the U.S.A.
AUGUST 2022 THE DRAG SPECIALTIES 16 9901-3006 ONE-PIECE ALUMINUM FRONT WHEELS • Forged wheels place the highest material strength in the same direction as the operating load, creating a light, strong wheel • Feature the contour rim lip for a graceful arc from rim to lip • Available in chrome, Platinum Cut™, Black Ops™ or Gold Ops™ • Platinum Cut™ finish starts with a polished wheel that has been black anodized, then recut to pen up the design and the recut is polished to a brilliant shine • Black Ops™ finish features gloss black on top of a contrasting textured black finish for outstanding durability and looks DESCRIPTION PARAMOUNT PLATINUM CUT PARAMOUNT CHROME FORMULA PLATINUM CUT FORMULA CHROME PRO-AM BLACK OPS PRO-AM GOLD OPS SUG. RETAIL 21” X 3.5” for 14-21 FLHT/FLHR/FLHX/ FLTRX/FLTRU/FLTRK w/o ABS (dual disc) 0201-2419 0201-2420 $1,849.95 21” X 3.5” for 14-21 FLHT/FLHR/ FLHX/FLTRX/FLTRU/FLTRK w/ ABS (dual disc) 0201-2426 0201-2422 0201-2421 0201-2425 0201-2423 0201-2424 1,849.95 PERFORMANCE MACHINE Performance Machine continues to be at the front of the custom wheel market for American V-Twins. The second-to-none designs and machined to exact tolerances for a beautiful look and reliable performance. A wide range of show-quality finishes let you get the exact look to match your bike. Now available for the latest M-Eight Touring applications. • Gold Ops™ finish features gloss gold on top of a contrasting textured gold finish for outstanding durability and looks • Made in the U.S.A. NOTE: Models with TPMS will require PART #0360-0056 (sold separately) NOTE: Front wheels listed as fitting 14-20 Dresser models will require the use of PM front brake rotors (3.25” bolt circle) NOTE: 14-19 FLHT/FLHR/FLHX 21” front wheels include fender relocation brackets for use with stock fenders. PARAMOUNT PLATINUM CUT PARAMOUNT CHROME FORMULA PLATINUM CUT FORMULA CHROME PRO-AM BLACK OPS PRO-AM GOLD OPS
www.dragspecialties.comRkJQdWJsaXNoZXIy OTcxOTk3