2023 Drag Specialties FatBook

2023 NEW PRODUCTS WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for 2023. SECTION 1 NP142 See OLDBOOK For Early Model Applications WARNING: ALL TANKS ARE SHIPPED UNPAINTED. CAPS ARE NOT INCLUDED UNLESS NOTED. ALL GAS TANKS SHOULD BE FITTED, PRESSURE-TESTED AND SEALED BEFORE BEING PAINTED TO ELIMINATE POTENTIAL PROBLEMS. VENTED DIPSTICKS • Billet dipsticks vent/​breathe excessive crankcase pressure from the oil tank through a PCV style breather consisting of an oil separator system, perforated disc, replaceable filter element and umbrella flapper valve • Pushes into the factory oil fill spout as a stock replacement part • These breathing dipsticks remove unwanted build-up of blowby pressure • Larger cubic inch engines as well as engines with worn and/or loose ring clearances will have increased blowby • Blowby is pressure that is forced past the rings and cylinders, pushed into the crankcase and then forced back into the oil tank • Feuling test results show a decrease in engine oil sump levels, more freely/​smoother revving engine, increased MPG and decreased blowby • Dipsticks vent/​breath excessive crankcase pressure from the oil tank through a breather system consisting of a oil separator system, perforated disc, replaceable filter element and umbrella flapper valve • Kits includes two venting styles options to choose from when installing the dipstick • Option 1: 1/8" NPT breather vent fitting with internal porous filter element (this option gives a clean look, however it can produce an oil misting/​residue out of the element on engines with excessive leakdown/​blowby) • Option 2: Quick-disconnect coupler fitting with rubber hose and filter element (this option will run any excessive oil misting/​residue through the line and into the filter element, however this option does requires disconnecting the fitting in order to check the oil GAS KAP KEEPER • No more dropped or lost caps, tank dings or gas on your seat • Inner magnet encapsulated by rubber on all sides • Holds cap to any steel surface • Attaches to gas cap with 3M® Automotive two-sided tape; gas cap not included • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0701-0952 For 18-22 Softail models $699.00 PART # DESCRIPTION SUG. RETAIL FOR 99-06 FLT/F​ LHT/​FLHR/​FLTR/​FLHX AND H-D TRIKE MODELS 1012-0258 Polished $299.95 1012-0259 Black 299.95 PART # DESCRIPTION SUG. RETAIL FOR 99-05 DYNA MODELS 1012-0257 Polished $299.95 1012-0260 Black 299.95 PART # DESCRIPTION SUG. RETAIL 0703-0897 Gas Kap Keeper $14.95 • For Option 2, Feuling recommends routing the line up the frame rail, up under the seat/​ABS area then back down along the right side frame rail and the filter element can fit cleanly between the engine/​ trans matting area on the inside of the lower right frame rail • Checking oil level: There are two ways to read the oil level with this dipstick, with the bike on the jiffy stand (FHS) or the bike upright and level (FHU) • FHS = FULL HOT STAND • FHU = FULL HOT UPRIGHT • Available in polished or fade-resistant black • Made in the U.S.A. • See page 1530 of the 2023 Drag Specialties FatBook for the entire line of Feuling Vented Dipsticks NOTE: These dipsticks do get hot; use a glove when checking oil level. NOTE: It is important to get the correct hot oil level in your bike. Feuling recommends running the oil level 90%-99% full when hot. NOTE: The oil pick up port is on the right side of the engine. Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank. 1012-0258 1012-0260 STRETCHED GAS TANK • Stretched gas tank comes in raw steel, unpainted. It includes a pop-up gas cap and works with the OEM fuel pump • We recommend the use of a tank sealer prior to installation • The tank has a capacity of approximately 3.5 gallon (13 liter) and comes with installation instructions and hardware NOTE: When used on Softail models with a dash, modifications are necessary to relocate/​replace the dash. Stock seats do not work with our stretched gas tanks.

RkJQdWJsaXNoZXIy OTcxOTk3