2022 Drag Specialties FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for 2022. SECTION 7 776 See OLDBOOK For Early Model Applications DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGES 5-6 FOR IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE. PART # DESCRIPTION SUG. RETAIL FOR 07-17 TWIN CAM AND 06 DYNA 0925-0842 1, 5 For chain or gear drive cams $259.95 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-0839 2 For gear drive cams 259.95 0925-0840 2, 3 For chain drive cams w/ spring tensioners 279.95 0925-0841 4 Hydraulic tensioner conversion camplate for stock chain drive cams 259.95 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 For use with factory or any Twin Cam oil pump with the 99-06 bolt pattern. Compatible with Feuling oil pump PART #s 0932-0018, 0932-0089, 0932-0020. 3 Includes tensioner pins and hardware guide. 4 Requires 07-17 style oil pump, hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kits 0925-1069 or 0925-1070. Compatible with Feuling oil pump PART #s 0932-0090, 0932-0023, 0932-0026. 5 For use with factory and or any Twin Cam oil pump with ‘07-’17 bolt pattern; compatible with Feuling oil pump PART #0932-0090, 0932-0023, 0932-0026. OE+ CAMPLATES FOR TWIN CAM • Billet camplates are manufactured from 6061 aluminum providing increased rigidity and machined to Feuling ® high tolerance standards • Designed and manufactured to the highest standard of quality with proven Feuling ® performance • The pressure relief valve and spring are pre-set, matched and seated by Feuling ® with a full pop off pressure of 50-60 psi • Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerance for improved press fit • Bearing retainer plate and hardware included • Camplate for 99-17 Twin Cam (and 06 Dyna) have tighter cam journal bore tolerance for improved cam fitment • Added cam journal oil groove for cold start up protection and increased cam journal lubrication PART # DESCRIPTION SUG. RETAIL FOR 07-17 TWIN CAM AND 06 DYNA 0925-0110 1, 2 For chain or gear drive cams $369.95 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0920-0006 3 For gear drive cams 359.95 0925-0109 3, 4 For chain drive cams w/ spring tensioners 379.95 0925-0440 5 Hydraulic tensioner conversion camplate for stock chain drive cams 369.95 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 Requires the use of 07-17 style Feuling HP+ or Race Series oil pump PART #s0932-0023 or 0932-0026. 3 Requires the use of 99-06 style Feuling HP+ or Race Series oil pump PART #s 0932-0018 or 0932-0020. 4 Includes tensioner pins and guide hardware. 5 Requires 07-17 hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kit PART #s 0925-1069 or 0925-1070. HIGH FLOW CAMPLATES FOR TWIN CAM • Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages • Camplate matches the oil portholes throughout the camplate to the port holes in the engine case increasing engine oil flow throughout the engine • 25-35 degree cooler engine temperatures and 20-30 degree cooler oil temperatures • Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE ® and other aftermarket camplates • The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings • Camplates are pressure tested and pressure relief valve is seated, sealed and set to pop off at 55-60 psi • When matched with the Feuling ® Race Series oil pump rear wheel power gains of 3 Horsepower and 4 ft/​lbs of Torque can be achieved • For use ONLY with the Feuling ® oil pumps • Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerances for improved press fit • Bearing and retainer plate hardware is included • Camplates for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal tolerance for improved cam fitment • Added cam journal oil groove for cold startup protection and increased cam journal lubrication • Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear • Made in the U.S.A. • Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear • Made in the U.S.A. 0925-0839 0925-0842 0925-0110 0925-0440