2022 Drag Specialties FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com SECTION 15 All part numbers in BLUE are new for 2022. 1505 See OLDBOOK For Early Model Applications WARNING: ALL TANKS ARE SHIPPED UNPAINTED. CAPS ARE NOT INCLUDED UNLESS NOTED. ALL GAS TANKS SHOULD BE FITTED, PRESSURE-TESTED AND SEALED BEFORE BEING PAINTED TO ELIMINATE POTENTIAL PROBLEMS. PART # DESCRIPTION SUG. RETAIL 0701-0759 For 10-21 FLHT/​FLHX/​FLTRX/​FLTRU/​FLTRK (except 21 FLHR/​FLHXS/​FLTRXS) $999.95 RAZOR BACK STRETCHED TANK KIT • This deep drawn, real steel stretched tank kit is the ultimate complement to your Bagger project • Tank flows seamlessly from front to back and the stretch wings flow into the side covers • Direct bolt-on replacement for all 10-21 HD touring models except Road King, Street Glide Special and Road Glide Special; no modification required, unless noted • Each 6.5 gallon tank is handcrafted and factory pressure tested and corrosion protected and sealed PART # DESCRIPTION SUG. RETAIL 0701-0001 Smooth, uses 73-81 style gas cap $148.95 PART # DESCRIPTION SUG. RETAIL 0701-0657 Ribbed, uses 82-E96 H-D threaded gas cap $150.95 MUSTANG GAS TANKS • Fat Bob-style custom application, low-tunnel tank holds approximately 3.3 gallons • Features a 3 / 8 ” NPT-style petcock mount with two 1 / 4 ” NPT crossover fittings • Measures 19 3 / 4 ” L (including mounting tabs) x 11 1 / 2 ” W x 7 1 / 2 ” H (approximately) • Available as a single-cap design NOTE: Not for use on fuel-injected models. PART # DESCRIPTION SUG. RETAIL FOR 01-06 FXST, FLST W/ FUEL INJECTION AND 04-06 FXST, FLST W/ CARB (EXCEPT FXSTD) 0701-0167 1 2” extended w/ one screw bung and dummy bung for Original Equipment gas gauge (carb only) $431.95 1914-1864 1 2” extended dash style w/ fuel gauge bung, single screw-in cap (carb or EFI) 500.95 0703-0735 Repl. blockoff plate w/ gasket for PART #1914-1864 12.95 FOR 00-03 FXST, FLST W/ CARB (EXCEPT FXSTD) 1914-1814 2” extended dash style w/ fuel gauge bung, single screw-in cap 469.95 1 Requires the use of petcock adapter OEM #62842-00 or Drag PART #0705-0024 when used in listed carb applications. ONE-PIECE TANKS • 5.1-gallon tank is made from 16-gauge stamped steel • Available in 2” extended length • Dash-style tank has mounting provisions for stock-style dash and ignition switch (not included) 0701-0001 0701-0657 0701-0167 0701-0167 side profile 1914-1864 • Tank with fuel gauge bungs accepts OEM-style or aftermarket fuel gauges NOTE: Seat nose may require modification to fit properly with extended tanks. Some models may require sending unit modification. • Kit includes tank, steel dash, chrome pop-up cap, rubber dash trim and hardware • Requires modification to your stock seat or a custom seat (sold separately) NOTE: U.S. Patent #D737,192. NOTE: FLHR models will require relocation of speedometer and ignition switch.