2022-2023 Drag Specialties OldBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for the OldBook. SECTION 5 318 See FATBOOK For Late Model Applications DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGES 5-6 FOR IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE. PART # DESCRIPTION SUG. RETAIL 3850-0481 Dealer service kit for S&S exhaust $42.95 EXHAUST DEALER SERVICE KIT • Everything needed to perform a required exhaust system service or end cap replacement • Kit includes tamper-proof screws and S&S proprietary tamper-proof screw bit PART # DESCRIPTION SUG. RETAIL V22533 Allen cap screw kit $5.99 1860-0547 Dog Bone kit 14.99 REPLACEMENT COMPONENTS FOR VANCE & HINES EXHAUST SYSTEMS • Replacement Allen cap screws for the “Supersport” and “SS2-R” exhaust systems • Use these screws to reattach the can to the nose tip and end cap; sold as a set of 12 • Dog Bone includes two nut plates and four 5 / 16 ” -18 x 5 / 8 ” bolts • Fits all Vance & Hines systems and slip-on mufflers that use the dog bone style attachment system • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0930-0059 For 48-65 Panhead $11.95 EXHAUST SPIGOT • Designed and machined from 6061-T6 aluminum extruded tubing • Allows you to rebuild the exhaust attachment point on your classic Panhead engine PART # DESCRIPTION SUG. RETAIL 1861-0400 Torque cones $38.95 1861-0770 Vortex torque cones 64.95 TORQUE CONES • High-temperature stainless steel cones have fully radiused edges for improved engine response, especially low-end torque • Generate correct levels of backpressure for increased horsepower • Fit most stock and aftermarket exhaust systems; fit 1 3 / 4 ”-2” ID exhaust pipes • New Vortex design increases back pressure, improving torque and horsepower • Smooths out the power curve for more consistent performance • Sold in pairs • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1861-0806 Sound reduction kit $30.95 SOUND REDUCTION KIT • Easy, bolt-in sound reduction for 3” HP-Plus ® mufflers • Takes off 4dB at idle and improves low-end torque – minimal loss of top-end horsepower • The machined discs with tapered bosses fit into each end of the patented resonator near the exit end of the mufflers and are retained by the supplied bolts and nuts • This kit is designed to use with three-ball style resonators that are 6.50” long • Will also fit most other mufflers (four-ball style resonators) if 1 / 4 ”-20 x 11.00” threaded rods are substituted for the supplied bolts • Installation requires removal of the mufflers • Kit includes machined discs and two 7.50” 1 / 4 ”-20 bolts and two prevailing torque nuts • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1861-0739 For 1 3 / 4 ” OD pipes; 8” L $15.95 1861-1190 For 2” OD pipes; 6” L 12.95 1861-0913 For 2” OD pipes; 9 3 / 4 ” L 13.95 1861-0914 For 2 1 / 4 ” OD pipes; 8 1 / 4 ” L 12.95 1861-0915 For 2 1 / 2 ” OD pipes; 8 1 / 2 ” L 17.95 1861-0916 For 3” OD pipes; 8” L 20.95 EXHAUST BAFFLES • Fiberglass-wrapped steel construction • Available for a variety of pipe sizes • May require drilling a hole in the exhaust pipe • Sold each PART # DESCRIPTION SUG. RETAIL DS-202019 Repl. baffle for 1 3 / 4 ” drag pipes $10.95 REPLACEMENT BAFFLE FOR DRAG SPECIALTIES EXHAUSTS • Steel baffle for 1 3 / 4 ” drag pipes • Sold each PART # DESCRIPTION SUG. RETAIL DS-202011 1 3 / 4 ” (ea.) $40.95 DS-202012 1 3 / 4 ” (pr.) 76.95 PART # DESCRIPTION SUG. RETAIL DS-202032 2” (pr.) $76.95 HP-PLUS ® DRAG PIPE BAFFLES • Dampen sound without impeding flow-through performance • All steel construction; baffles feature HP-Plus ® design • Install easily on 1 3 / 4 ” or 2”, 16- or 18-gauge drag pipes • Baffles held by 1 / 4 ”-20 screws and locking nuts • Made in the U.S.A. 1861-0739 DS-202012 1861-0400 1861-0770 V22533 • Welding required • Sold each • Made in the U.S.A. 1860-0547