2021 Parts Unlimited Tire

V-TWIN TOOLS dragspecialties.com BOLD MAGENTA part numbers are new for 2021 2021 TIRE & SERVICE CATALOG 598 CAM OR PINION BUSHING INSTALLER DRILL JIGS • Use to install bushing and drill dowel pin hole to factory specification • Use staking dowel pin PART #DS-196313 • #31 jobber length HSS drill bit included with jigs • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196099 For cam bushing OEM #25581‑70; 70‑99 Big Twin (except Twin Cam) $54.95 DS-196101 For cam bushing OEM #22586‑37; 37‑48 Big Twin side‑valve motors, 54‑20 XL, 91‑09 Buell (except 1125R) 54.95 PART # DESCRIPTION SUG. RETAIL DS-196100 For pinion bushing OEM #25582‑54/73; 54‑92 Big Twin $54.95 DS196313 Staking dowel pins (10‑pk.) 15.95 CAM/​CRANK SPROCKET LOCK TOOLS • Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts • Made of non-marring Delrin ® • Instructions included • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0060 For 06 Dyna and all 07‑17 Twin Cam $77.95 DS-196201 For 99‑06 Twin Cam (except 06 FXD) 57.95 PINION BUSHING PULLER • Use to remove pinion bushing from cam cover in one easy operation • Use with cam cover holder PART #DS-196144 • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196157 For 54‑99 Big Twin $178.95 INNER CAM BEARING INSTALL TOOLS • Used to install inner cam bearings • For use with handle PART #DS-196042 • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196044 Cam bearing tool only for 58‑99 Big Twin (except Twin Cam) $76.95 PART # DESCRIPTION SUG. RETAIL DS-196043 Cam bearing tool only for 57‑90 XL, 87‑90 Buell $73.95 DS-196042 Handle/​driver only 84.95 CAM AND PINION GEAR GAUGE PINS • Use to check pinion gear for pitch diameters • A complete sizing chart is included with the .105” gauge pins • Check service manual for sizing chart • Sold in sets of two • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-197011 .105” for 54‑89 Big Twin $31.95 DS-197012 .108” for 90‑99 Big Twin Evolution 31.95 GAUGE PINS • Used to measure the outside diameter of cam drive gears • Precision machined from a high-quality steel alloy • Available in .105” or .108” dia. • Sold in pairs • Made in the U.S.A. NOTE: There are two basic differences between 90-99 cam gear sizes and earlier years. The overall range of gear pin measurements (from the largest gears to the smallest) was reduced in ‘90 from .006” to .003”. The large gears are the same size for both 84-89 and 90-99 (green and black color codes). Gear size measurements (over pins) are listed in the 1990 H-D manual using .108” pins instead of .105” pins (as for earlier years). For the same gear, measurement over .108” pins will be approximately .012” larger than for .105” pins. For 92 engines, stock cam gears are interchangeable with earlier versions but gear outer diameters have been reduced by .025”. PART # DESCRIPTION SUG. RETAIL DS199105 .105” gauge pins (pr.) $21.95 DS-199106 .108” gauge pins (pr.) 23.95 DS‑196099 DS‑196101 DS196313 DS‑196044 DS‑196043 DS‑196042 DS‑197011 DS199105 DS‑196201