2021 Drag Specialties FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com SECTION 7 All part numbers in BLUE are new for 2021. 731 DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGE 5 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION. See OLDBOOK For Early Model Applications POWERGLIDE II HYDRAULIC TAPPETS • These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities • Billet body • Increased roller width • Roller perpendicularity held to .0002” • Hand-honed hydraulic unit cavity • Dynamic load capacities increased over 30% • Lubrication capacities for hydraulic unit and valve train (top end) increased 10% • Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling • Sold each • Made in the U.S.A. HYDROSOLID TAPPETS • Performs like a hydraulic tappet up to 5500 rpm, then turns into a solid tappet • When it turns into a solid tappet, it adds approximately three to six more usable horsepower • Prevents hydraulic pump at high rpm HIGH-QUALITY TAPPET ROLLER KITS • Made from 52100 bearing material • Include 4340 chromoly axles • Sold in a 4-pack POWERGLIDE ™ STEADY ROLL TAPPETS • The same Powerglide advantage (oil-fed axle, billet steel body, precision fit hydraulics) but now incorporates a Steady Roll bronze bushing in place of the needle bearing roller • These tappets have undergone extensive development to increase load, lubrication, hydraulic and life capacities • Billet body • Increased roller width • Roller perpendicularity held to .0002” HYDRAULIC LIFTER LIMITED-TRAVEL SPACER • Spacers are designed to limit the range of travel of the hydraulic tappet plunger • Helps with starting and high-speed operation by not letting the hydraulic lifter bleed down or collapse • Sold in sets of four • Made in the U.S.A. NOTE: Requires the use of adjustable pushrods, see page 726. TAPPET CUFFS LIFTER GUIDES • The factory tappet guides are constructed of plastic, which allows tappets to twist under heavy stress • These tappet cuffs capture the tappets without impacting vertical motion to keep them aligned, even in high-rpm situations • Billet aluminum construction with a hard anodized black coating • Easy upgrade when changing tappets or doing a cam change • Made in the U.S.A. NOTE: Due to variances between cam and tappet manufacturers, always check the tappet to tappet cuff clearance. PART # DESCRIPTION SUG. RETAIL FOR 17‑20 M‑EIGHT, 99‑17 TWIN CAM, 00‑20 XL/XR 1200 AND 00‑09 BUELL 0929-0014 Standard $126.95 0929-0023 +.005” oversize 142.95 PART # DESCRIPTION SUG. RETAIL 0929-0015 For 17‑20 M‑Eight, 99‑17 Twin Cam, 00‑20 XL/XR, 1200 and 00‑09 Buell $125.95 DS-194347 For all 91‑99 XL and 94‑99 Buell (.9035” OD); repl. OEM #18529‑89 119.95 DS-194342 For 86‑90 XL (.8425” OD); repl. OEM #18523‑86 117.95 BIG AXLE ™ POWERGLIDE ™ TAPPETS • Micro-finish bore allows a running fit of .0002” • Big Axle ™ rollers are designed around three working parts • The outer wheel/​roller has a 27% greater wall size – less harmonic distortion for better tracking of cam lobe • Pin bearings are decreased in size by 12%, which increases rpm for more precise tracking • Axle size is increased 36% and doubles as the inner race, so the pin bearing and complete roller assembly now rotate around the axle instead of an inner race, eliminating all possible movement in and around the axle • Sold each • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 0929-0053 For 86‑90 XL $107.95 PART # DESCRIPTION SUG. RETAIL FOR 17‑20 M‑EIGHT, 99‑17 TWIN CAM, 00‑20 XL, 09‑12 XR 1200 AND 00‑09 BUELL 0929-0046 Standard $127.95 0929-0047 +.002” oversize 159.95 0929-0048 +.005” oversize 159.95 PART # DESCRIPTION SUG. RETAIL FOR 86‑90 XL AND 87‑90 BUELL 0929-0043 Standard $107.95 0929-0044 +.002” oversize 119.95 PART # DESCRIPTION SUG. RETAIL 0929-0006 For 03‑17 Twin Cam and S&S Evo‑style lifters w/ .612” ID tappets $22.95 PART # DESCRIPTION SUG. RETAIL 0929-0075 For 17‑20 FLHT/​FLHR/​FLTRX/​FLTRU/ ​FLTRK/​FLHX, 18‑20 Softail $61.95 PART # DESCRIPTION SUG. RETAIL FOR 91‑99 XL, 94‑99 BUELL; REPL. OEM #18526‑89 DS-194278 Std. (.9035”) $109.95 FOR 86‑90 XL; REPL. OEM #18523‑86 DS-194107 Std. (.8425”) 101.95 • Sold each • Made in the U.S.A. NOTE: Requires the use of adjustable pushrods. DS‑194107 DS‑194278 • Hand-honed hydraulic unit cavity • Dynamic load capacities increased over 30% • Lubrication capacities for hydraulic unit and valve train (top end) increased 10% • Lubrication capacities for the roller, cams and cam bearings have increased 100% for increased cooling • Sold each • Made in the U.S.A. 0929‑0014 0929‑0043 0929‑0046 0929‑0015 DS‑194347 DS‑194342