2020 Drag & Parts Unlimited Update

SERVICE & MAINTENANCE TOOLS 2020 TIRE & SERVICE UPDATE BOLD MAGENTA part numbers are new for 2020 TIRE & SERVICE www.dragnetweb.com www.partsnetweb.com 407 PART # SUG. RETAIL 3850‑0508 $45.99 PRO SEAL PULLER • Makes it easy for you to remove oil and water seals • Includes three interchangeable puller tips to accommodate a wide range of seal sizes • Wide tip footprint aids easy seal removal • Knurled handle provides secure grip and leverage • Billet aluminum construction reduces risk of damage to engine cases • Durable anodized finish with laser-etched logos • Patent pending PART # SUG. RETAIL 3803‑0212 $16.95 CHAIN-DRIVE CLUTCH LOCK TOOL • For all BDL complete chain drive kits and chain drive baskets with BDL chain drive clutch hubs • Used to lock up clutch hub and basket assemblies to help properly torque clutch hub nut to a specified torque specification • Not an impact wrench that can damage the clutch hub PART # SUG. RETAIL 3807‑0523 $12.89 OPTIMATE SOLAR CHARGER SUCTION CUP MOUNT • For mounting Optimate Solar chargers; for the complete line of Optimate Solar chargers, see page 469 of the 2020 Parts Unlimited/​ Drag Specialties Tire & Service catalog PART # SUG. RETAIL 3807‑0524 $31.90 OPTIMATE USB O-108 KIT • Charge a phone, GPS, camera or tablet on your motorcycle or up to 80” away with this weatherproof charger • Low input (less than 12.3V) auto-off protects vehicle battery from total discharge • 12V power through an industry standard SAE two- pin connector and a 40” supply cable • 5V 3300mA true output via a 40” USB output cable with sealing cap for USB socket • Short circuit, overheat and over-voltage protection • Apple 1A charge confirmation “handshake” built in • Includes O-31 battery lead with 10A fuse • Has reprogrammed battery status lights to work better with lithium batteries • See page 472 of the Parts Unlimited/​Drag Specialties Tire & Service catalog for the complete line of Optimate USB O-108 chargers OPTIMATE LITHIUM BATTERY STATUS/​CHARGE SYSTEM MONITORS • Smart battery leads that measure voltage and stored charge of 12.8V/13.2V Lithium (LFP/​LMiFePO4) batteries • Monitor charge or confirm if the charging system is working correctly • Two automatic modes: battery charge level monitor and charging system test • Remain flexible and usable down to temperatures of -40°F/-40°C • SAE charge port with weatherproof sealing cap • Jar of 20; Sug. Retail price is each PART # SUG. RETAIL 3807‑0522 $19.89 PART # SUG. RETAIL 3801‑0390 $28.99 14MM PRO PLUG SOCKET • Ultra-strong tool steel construction • Slim skeleton profile • Use with a 3 / 8 ” square drive or 17mm wrench • Can be used as an axle holding tool on bikes with 17mm internal hex axles • Innovative internal plug retention system • Protective black oxide coating PART # SUG. RETAIL 3850‑0515 $99.99 U-JOINT SEPARATOR • Designed to press bearing cups out without damage to the bearings or the yoke • Compact design allows U-joints to be disassembled on the vehicle • Durable hardened-steel construction with black oxide coating • Fully adjustable arms will fit most UTV and ATV applications • Original Motion Pro Design • Not for use with impact guns • Tool used for U-joint disassembly only PART # SUG. RETAIL 3850‑0514 $21.99 U-JOINT CLIP INSTALLER • Designed to install inner circlips on UTV and small vehicle U-Joints • Magnet holds clips securely in place during installation • Ultra-thin profile for easy clip installation. • Patent pending V blade works with virtually all UTV U-Joints • Durable plastic handle with integrated steel strike plate • Hardened tool steel blade for durability PART # SUG. RETAIL 3850‑0513 $249.99 MULTI-POINT ILLUMINATION MOTION GARAGE CEILING LIGHT • 5400K daylight white; 7500 total Lumens • Multi-point illumination (MPI) creates five points of light, all from your existing fixture • Installs in minutes and is powered by a standard ceiling fixture • 360° adjustable motion sensor sensitivity up to a 20’ radius; features a two minute timer • Motion sensor features different modes for minimum to maximum sensitivity and an Off mode • MPI hub dimensions: 7.6” x 7.5” x 4.25”; pod dimensions: 4.1” x 3.9” x 2” • Cord length of 9.5’ • Easy-to-read laser- etched markings • Through-hole allows use of screwdriver or holding rod • Light weight • Patent pending • Please see page 484 of the 2020 Parts Unlimited Tire & Service catalog for Motion Pro’s full line of Pro plug sockets