2020 Drag FatBook

WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATEFRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES www.dragnetweb.com All part numbers in BLUE are new for 2020. SECTION 7 686 DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. SEE PAGE 418 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION. See OLDBOOK For Early Model Applications PART # DESCRIPTION SUG. RETAIL 0926-3138 For 17-20 M-Eight w/ factory style 6mm valve stems and triple groove $559.95 HIGH-LOAD BEEHIVE ® VALVE SPRINGS WITH TITANIUM RETAINERS FOR M-EIGHT • M-Eight High-Load springs are machined from a premium grade hi-tensile chrome silicon single conical ovate wire, shot-peened with a specially processed thermal heat treat and super NexTex ® finish to give these valve springs the needed fatigue life to exceed the high demands of V-Twin engines from stock to performance • Valve springs are a direct bolt in replacement, no spring seat or rocker cover machining required up to .565” lift • Springs will accommodate over .600 cam lift, but will require spring seat pocket machining on the cylinder heads to set correct spring open height • Smaller lighter weight retainers which drastically reduce the valve weight creating a quicker revving and smoother motion than comparable dual or single valve springs • Eliminate valve spring separation, maximize stability, reduce valve-train noise and harmonics • Packaged as a matched set and must be installed at the correct OPEN HEIGHT • Matching max cam lift to the open height spec of the valve springs is essential for optimal valve-train operation and spring life (see included spring spec chart) • Kit includes: matched set of Feuling ® High-Load BeeHive ® valve springs, Titanium retainers, machined spring seats, seat shims, valve locks and a set of premium Viton ® valve seals equipped with a spring loaded valve stem wiper system • Bolt in up to 565 lift for M-Eight • Fit up to .600” lift • M-Eight specs: seat lbs./installed height; 151 lbs. at 1.475” (.485” lift), 144 lbs. at 1.498” (.508” lift), 143 lbs. at 1.501” (.511” lift), 140 lbs. at 1.511” (.521” lift), 124 lbs. at 1.562” (.578” lift), 120 lbs. at 1.582” (.592” lift), 304 lbs at .990” open height, coil bind at .945” (cam specs measured on the lifter at .050” lift with 1.61 rocker arm ratio) • Recommended for .540”+ lift camshafts NOTE: These springs are ONLY recommended for large lift camshafts like Reaper ® 592 Cam PART #0925-1265 and RACE style engines as these valve springs have increased load and if used on smaller cams will create extreme rocker arm deflection. PART # DESCRIPTION SUG. RETAIL FOR 17-20 M-EIGHT 0926-2973 Standard, 6mm valve stem (uses factory retainers) $339.95 0926-2974 Standard, 6mm valve stem (includes titanium retainers) 539.95 FOR 05-17 88”/96”/103” TWIN CAM, 04-20 XL, 09-12 XR 1200 0926-0852 7°, 7mm valve stem w/ stock triple keeper groove 299.95 PART # DESCRIPTION SUG. RETAIL FOR 99-04 TWIN CAM AND 86-03 XL 0926-0851 7°, standard 5 / 16 ” valve stem and keeper groove $299.95 FOR TWIN CAM SCREAMIN’ EAGLE HEADS 0926-1466 5 / 16 ” valve stem and keeper groove and .530” diameter valve guides 299.95 ENDURANCE BEEHIVE ® VALVE SPRINGS WITH TITANIUM RETAINERS • Machined from premium-grade hi-tensile chrome silicon single-conical ovate wire • Shot-peened with specially processed thermal heat treat and super NexTex ® finish for fatigue life needed to exceed high demands of V-Twin engines • Use a much smaller and lighter weight retainer to reduce valve weight and create quicker rev and smoother motion • Direct bolt-in replacement up to .650” cam lift; no machining or rocker box clearancing required • Available for 5 / 16 ”, 7mm and 6mm valves • Kits include: Endurance BeeHive ® valve springs, lightweight 7° super Titanium heat-treated retainers, machined spring seats, seat shims, valve locks and a set of premium Viton ® valve seals equipped with spring-loaded valve stem wiper system • Twin Cam specs: seat lbs./installed height; 198 lbs. at 1.685” (.535” lift), 194 lbs. at 1.703” (.553” lift), 190 lbs. at 1.724” (.574” lift), 187 lbs. at 1.754” (.604” lift), 185 lbs. at 1.780” (.630” lift), 160 lbs. at 1.800” (.650” lift), 375 lbs. at 1.150” (open height) coil bind at 1.100” • M-Eight specs: seat lbs./installed height; 134 lbs. at 1.375” (.405” lift), 127 lbs. at 1.405” (.435” lift), 125 lbs. at 1.415” (.445” lift), 121 lbs. at 1.435” (.465” lift), 116 lbs. at 1.455” (.485” lift), 113 lbs. at 1.470” (.500” lift), 109 lbs. at 1.490” (.520” lift), 103 lbs. at 1.520” (.550” lift), 226 lbs. at .970” (open height), coil bind at .920” • Feuling ® BeeHive ® valve springs must be installed at the correct OPEN HEIGHT, matching max lift to the open height spec of the valve springs • Made in the U.S.A. NOTE: Feuling ® BeeHive ® valve spring kits are direct replacement with no machining or rocker box clearance required up to .574” lift for 98-04 Big Twin and 86-03 XL and up to .650” lift for 05-17 Twin Cam. Larger camshafts require valve guide machining for seal to retainer clearance. 0926-2973 0926-1466